Questions tagged [output]
A signal or power being generated by one system for consumption by another, or a connection for that purpose.
629 questions
3
votes
2
answers
117
views
"Diode-OR" with LMV393 Outputs
In the circuit below, the inputs at pins 2 and 6 are being driven such that either one of pins 1 or 7 will pull low at one time. The diode is intended to pull pin 1 low with pin 7 so that both circuit ...
- 51
0
votes
2
answers
86
views
What the Vout would be in this circuit?
Vin = +120Vdc
Resistor 1 = 1.3k/10w (2x2.7k/5w parallel)
Capacitor 1 = 1000uf/63v (polar.)
Resistor 2 = 4.7k/3w
Capacitor 2 = 1000uf/63v (polar.)
- 47
1
vote
2
answers
203
views
Output Voltage Range of a Linear Regulator
In the 5V linear regulator LM7805 datasheet, there is a voltage variation range for the 'Output Voltage' (min 4.8V, max 5.2V) parameter as can be seen in the following table. Under the 'Output Voltage'...
- 197
0
votes
1
answer
87
views
Isolation transformer isolation [closed]
I'm looking to get a medical-grade isolation transformer to eliminate ground loop issues in my PC/audio setup.
I understand that this type of transformer provides galvanic isolation and features ...
- 3
2
votes
1
answer
94
views
What are advantages of using input as differential bipolar instead of a single ended input?
There is a galvo driver's input as shown below:
The driver manual recommends dual bipolar -10 V to 10 V DAC analogue output channels (differential) as inputs to for the driver.
And it offers two ...
- 2,043
5
votes
1
answer
143
views
Analog Output Protection Against Continuous External Bipolar Overvoltage
I have an analog output that I need to protect from continuous overvoltage in case of incorrect connection by amateur installers. For those who are interested, I am currently working on a part of the ...
- 414
0
votes
1
answer
86
views
What capacitor would the best replacement for an inverter?
I have a Renogy 3000w inverter 12v to 230v (50Hz)
R-INVT-PUH1-301235-UK
Its a relatively budget model, but a step up from the really cheapy ones.
It has let out the magic smoke, after around 2 years (...
- 11
-1
votes
2
answers
216
views
How to regulate output voltage in this circuit?
Look at the schematic of the circuit board. The circuit board is for charging a 6-volt 4 Ah lead-acid battery (in an emergency light with 2 6-watt fluorescent bulbs).
Now the output voltage for ...
- 47
2
votes
2
answers
249
views
How to calculate output voltage of a transformer for a given load?
I have this transformer: https://www.tme.eu/en/details/bv2020162/pcb-transformers/hahn/bv-202-0162/ . When no load is attached it measures ~38V on output. If I would like to reduce this no load ...
- 505
1
vote
2
answers
173
views
LTSpice simulations of Output impedance
I am performing some simulations using LTspice of a Circuit to which I would attach a Transient Limiter. Frequency range (150kHz-30MHz)
The goal is for the EUT to see close to 50Ω impedance on the ...
- 700
2
votes
1
answer
84
views
Where do I connect the other output if there is only one output on an electrical schematic?
I'm kind of a newbie at reading electrical schematics, I'm trying to build a small one-transistor amplifier just to see how it works, and a lot of the schematics I come across have only one output pin....
0
votes
0
answers
53
views
LTM4644EY#PBF not give correct output?
I am using LTM4644EY#PBF in my design. I designed the circuit based on the datasheet and reference designs. I have attached the datasheet and reference design link for your reference.
Evaluation board ...
- 71
4
votes
3
answers
351
views
Low impedance rail to rail logic output implementation?
I understand that the true implementations on chips are proprietary, but lets say that I want to implement a logical inverter out of discrete parts. The common circuit that I see is something like ...
- 155
-3
votes
1
answer
85
views
How do you compare DC battery voltage to voltage output from DC motor? [closed]
What is the difference and similarities with applying dc battery voltage and applying DC motor output voltage to a circuit or a DC motor with the same voltage (the same voltage we don't care about in ...
1
vote
2
answers
109
views
Adding an output to a SMPS transformer
I'm working on this SMPS circuit (recommended by STMicroelectronics). If you have any suggestions for improvement feel free to comment that.
As you can see, the output has 12.05V, but I want to add ...
- 165